Interlogix Concord 4 REV J Installation Manual Manuel d'utilisateur télécharger pdf (Page 19)

Chapter 2: Installation

Concord 4 Installation Manual 13

Optional SnapCards

Use the SnapCard header on the right side of the panel (Figure 4 below) to install

an optional SnapCard. Install the SnapCard onto the panel SnapCard header

and secure it in place with two screws, included with the SnapCard. To connect

all necessary input/output wiring, refer to the SnapCard documentation.

Figure 4: Installing a SnapCard

Mounting hole

Snapcard connector

Snapcard

Mounting hole

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 152 153

P/N 466-2182 • REV J • NOV12 1
Content 3
Important information 5
Chapter 1 7
Introduction 7
Planning the installation 8
SuperBus 2000 bus devices 9
Chapter 1: Introduction 10
Chapter 2 11
Installation 11
Installation overview 12
Chapter 2: Installation 13
Chapter 2: Installation 14
Mounting the panel 16
Grounding the panel 17
Antenna shrouds 18
Optional SnapCards 19
Panel terminals 20
Intrusion detection devices 21
Smoke detectors 21
Four-wire smoke detectors 23
Speakers and sirens 24
SPKR SPKR SPKR SPKR 25
Not used 25
To zone input 26
SuperBus 2000 touchpads 28
SuperBus 2000 modules 28
Power supply terminals 29
To power inputs on devices 29
GND +12V A BUS B 29
Hardwired interior 32
RJ31X phone jack 34
AC power transformer 36
Backup battery 37
Power up 37
Chapter 3 39
Programming 39
Overview 40
Programming touchpad 41
Quick programming mode 42
Tier 1 programming menus 43
DEMO KIT MODE OFF/ON (new 44
Chapter 3: Programming 45
Tier 2 programming menus 46
Shortcut numbers 50
Security menu 51
KEYCHAIN TP PTN), then 54
PARTITION 54
Phones menu 56
PHONE NUMBER _ 57
NUMBER _ 58
Phone options menu 60
Timers menu 63
SLEEP TIME 64
NO USAGE 64
Light control menu 65
Touchpad options menu 66
Reporting menu 67
Siren options menu 72
Sensors menu 73
S01 P1 G13 NC HW BACK DOOR 75
EDIT SENSORS 75
SENSOR GROUP nn 75
Audio verification menu 77
AUDIO VERIFY 78
Accessory modules menu 79
DEVICE ID (current ID) 80
DEVICE PTN and then press 80
PARTITION ASSIGN n 80
OUTPUTS 81
OUTPUT 1 81
PARTITION ASSIGN 1 81
CONFIGURATION tttrr 81
Onboard options menu 84
Macro keys menu 87
User programming mode 88
Time and date menu 89
User codes menu 90
Options menu 93
Set up schedules menu 94
Energy saver menu 98
Downloader programming 99
Chapter 3: Programming 100
Chapter 4 101
Testing and 101
Testing the system 102
Zones/sensors 103
Phone communication 104
Outputs and sirens 106
Light control 107
Energy saver module (ESM) 107
Touchpad display contrast 108
Troubleshooting 112
Access code issues 114
Arming and disarming issues 114
Bypassing issues 115
Alphanumeric touchpad issues 116
Speaker issues 117
Siren issues 117
Hardwired zone issues 118
Wireless sensor zone issues 118
Wireless touchpad issues 119
Phone issues 119
Light control issues 120
Energy saver module issues 120
Automation module issues 121
Appendix A 123
System planning sheets 123
Customer information 124
Wireless devices 124
Hardware devices 125
Zone and sensor assignments 127
Appendix B 135
Reference tables 135
Sensor group characteristics 136
Appendix B: Reference tables 138
Cross-zoning 139
Sensor text 140
System event triggers 142
Sensor group event triggers 143
Sensor number event triggers 144
Response characteristics 149
Response numbers 149
Specifications 151

Commentaires sur ces manuels

Pas de commentaire

Interlogix Concord 4 REV J Installation Manual Manuel d'utilisateur Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Panneau de contrôle Interlogix Concord 4 REV J Installation Manual