Interlogix NS2503-24P/2C User Manual Manuel d'utilisateur Page 182
- Page / 197
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
NS2503-24P/2C User Manual
182
Configure PoE -- System
poe limit-mode
Description:
Configure System PoE power limit mode information
Command Level
Global Configuration
Syntax:
poe limit-mode { classification / consumption}
Parameters:
< classification > Deliver PoE power by port priority setting and device PoE power level
< consumption > Detect the real power from the PDs.
Example:
Switch(config)# poe limit-mode classification
Switch(config)# show poe
Maximum Available Power
POE Admin mode
Temperature Unit1
Temperature Unit2
Over Temperature
PoE Power Consumption
Temperature Threshold
Usage
Usage Threshold
PoE Power limit mode
:360Watts
:Enable
:34C/93F
:37C/98F
:Enable
: 0 Watts
:50
:0%
: 100%
: Classification
Example:
Switch(config)# poe limit-mode consumption
Switch(config)# show poe
Maximum Available Power
POE Admin mode
Temperature Unit1
Temperature Unit2
Over Temperature
PoE Power Consumption
Temperature Threshold
Usage
Usage Threshold
PoE Power limit mode
:360Watts
:Enable
:34C/93F
:37C/98F
:Enable
: 0 Watts
:50
:0%
: 100%
: Consumption
- IFS NS2503-24P/2C User 1
- TABLE OF CONTENTS 3
- Introduction 8
- How to Use This Manual 10
- Product Features 11
- Product Specification 13
- INSTALLATION 15
- LED Indications 16
- Switch Rear Panel 18
- Install the Switch 19
- Rack Mounting 20
- SWITCH MANAGEMENT 23
- Management Access Overview 24
- Web Management 25
- Administration Console 26
- Protocols 28
- Web-Based Management 29
- Requirements 30
- Main WEB PAGE 32
- System Information 35
- Misc Config 36
- Console Port Info 40
- SNMP Configuration 41
- SNMPv3 Groups 44
- SNMPv3 View 45
- SNMPv3 Access 46
- SNMP V3 usm-user 48
- Syslog Setting 49
- System Log 50
- SNTP Setting 51
- Firmware Upgrade 52
- HTTP Firmware Upgrade 53
- Configuration Backup 54
- TFTP Backup Configuration 55
- Factory Default 56
- System Reboot 56
- Rate Control 59
- Port Status 60
- Port Statistics 61
- Port Sniffer 62
- Protect Port 64
- Remote Ping 65
- VLAN configuration 66
- Port VLAN ID 67
- Default VLANs 67
- Static VLAN Configuration 68
- Port-based VLAN 69
- 802.1Q VLAN 71
- VLAN Group Configuration 72
- VLAN Filter 75
- GVRP VLAN 76
- GVRP Setting 77
- GVRP Table 78
- Q-in-Q VLAN 79
- Q-in-Q Port Setting 80
- Q-in-Q Tunnel Setting 81
- To configure QinQ Port 81
- Trunking 82
- Aggregator setting 83
- Aggregator Information 84
- LACP enabled 85
- Switch 1 configuration 85
- Switch 2 configuration 86
- State Activity 88
- Forwarding and Filtering 89
- Static MAC Table 90
- MAC Filtering 91
- IGMP Snooping 92
- IGMP Configuration 96
- Static Multicast Table 98
- Spanning Tree Protocol 100
- NS2503-24P/2C User Manual 101
- Illustration of STP 103
- STP Parameters 104
- STP System Configuration 105
- Root Bridge Information 107
- Port Configuration 109
- DHCP Relay & Option 82 111
- Per Port Configuration 114
- Access Control List 115
- Users Configuration 118
- MAC Limit 121
- MAC Limit Port Status 122
- 802.1X Configuration 123
- System Configuration 125
- 802.1x Port Configuration 127
- Misc Configuration 128
- QoS Configuration 129
- QoS PerPort Configuration 132
- TOS/DSCP 133
- TOS/DSCP Configuration 134
- TOS/DSCP Port Configuration 134
- Power over Ethernet 136
- PoE Schedule 141
- CONSOLE MANAGEMENT 143
- Configure IP address 144
- Commands Level 146
- COMMAND LINE INTERFACE 147
- System Commands 148
- Switch Static Configuration 149
- Trunk Configuration 152
- VLAN Configuration 154
- VLAN Mode: Port-based 155
- Administration Configuration 159
- IP Configuration 160
- Reboot switch 161
- Reset to Default 161
- TFTP Update Firmware 161
- MAC limit 162
- Port Mirroring Configuration 163
- Quality of Service 164
- MAC Address Configuration 165
- STP/MSTP Commands 167
- System Options 172
- Community Strings 172
- Trap Managers 173
- 802.1x Protocol 175
- Non-Ipv4 ACL commands 178
- Binding 179
- Power over Ethernet Commands 180
- Configure PoE -- System 182
- Configure PoE -- Port 185
- (config)# poe priority low 1 186
- SWITCH OPERATION 188
- POWER OVER ETHERNET OVERVIEW 189
- The PoE Provision Process 190
- TROUBLE SHOOTING 193
- 10/100Mbps, 10/100Base-TX 194
Produits connexes et manuels pour Accessoires de communication Interlogix NS2503-24P/2C User Manual
Accessoires de communication Interlogix NS3502-8P-2S Installation Guide Manuel d'utilisateur
(15 pages)
(15 pages)
Accessoires de communication Interlogix GE-DSSG-244-POE Installation Guide Manuel d'utilisateur
(10 pages)
(10 pages)
Accessoires de communication Interlogix GE-DSSG-244-POE User Manual Manuel d'utilisateur
(412 pages)
(412 pages)
Accessoires de communication Interlogix NS4702-24P-4S-4X Command Line Guide Manuel d'utilisateur
(434 pages)
(434 pages)
Accessoires de communication Interlogix NS4702-24P-4S-4X Quick Start Manuel d'utilisateur
(16 pages)
(16 pages)
Accessoires de communication Interlogix NS4750-24S-4T-4X Quick Start Manuel d'utilisateur
(15 pages)
(15 pages)
Accessoires de communication Interlogix GE-DSH-73 Series Installation Sheet Manuel d'utilisateur
(13 pages)
(13 pages)
Accessoires de communication Interlogix GE-DSH-73 Series User Manual Manuel d'utilisateur
(179 pages)
(179 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels