Interlogix MC352-4P-2S Manuel d'utilisateur

IFS MC352-4P-2S User Manual P/N 1072702 • REV A • ISS 22OCT13

- 10 - 2.1.1 Switch Front Panel Figure 2-1 shows the front panels of MC352-4P-2S Industrial Gigabit PoE+ Switches. Figure 2-1:

- 11 -  DIP Switch The front panel of the MC352-4P-2Sprovides one 3-DIP Switch which is for configuring 100 or 1000X fiber support and fiber r

- 12 -  Per PoE Power Usage (Unit : Watts) (Lower LED to upper LED) LED Color Function 30 60 90 120 Lights to indicate the system is provid

- 13 - 2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Gigabit PoE+ Switch is used for two DC

- 14 - 2.1.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below.

- 15 - 2.1.6 Cabling 10/100/1000Base-T All 10/100/1000Base-T ports come with Auto-Negotiation capability. They automatically support 1000Base-T, 1

- 16 - Figure 2-3: Plug-in the SFP transceiver  Approved IFS SFP Transceivers IFS Industrial Gigabit PoE+ Switch supports both Single mode and

- 17 - IFS Model SFP Description S30-1SLC/A-10 SFP, LC Connector, Single Mode, Gigabit, 1 fiber, 1310nm/1550nm, 10km , A End S30-1SLC/A-20 S

- 18 - 100Base-FX: Before connecting with switches, workstation or media converter, please do the following steps: 1. With 100Base-FX Fiber Spee

- 19 - Figure 2-4: Pulling out from the transceiver Never pull out the module without pulling the latch or the push bolts on the module. Direct

- 2 - Copyright © 2013 United Technologies Corporation Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies C

- 20 -  Link status auto detect and redundant on Dual ports with same connector type.  Only Primary-Port is active at a time, the Backup-Port is

- 21 - Step 2: Lightly insert the bottom of the switch into the track Step 3: Check if the DIN-Rail is tightly on the track. Step 4: Please ref

- 22 - Step 5: Lightly pull out the bottom of the switch for removing it from the track. 2.2.2 Wall Mount Plate Mounting To instal

- 23 - 3. Applications In this paragraph, we will describe how to install Industrial Gigabit PoE+ Switch and the installation points. Industrial O

- 24 - Installation Steps Step 1: Unpack the Industrial Gigabit PoE+ Switch. Step 2: Check the DIN-Rail is screwed on the Industrial Gigabit PoE+

- 25 - 4. Switch Operation 4.1 Address Table The Industrial Gigabit PoE+ Switch is implemented with an address table. This address table is compos

- 26 - The Industrial Gigabit PoE+ Switch performs "Store and Forward"; therefore, no error packets occur. More reliably, it reduces the

- 27 - 5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Gigabit PoE+ Switch is not functioning pro

- 28 - 6. Cable Connection Parameters The wiring details are as below: 100FX Fiber Optical Cables: Standard Fiber Type Cable Specification Mu

- 29 - APPENDIX A: Networking Connection A.1 PoE RJ-45 Port Pin Assignments (End-Span) PIN NO RJ-45 POWER ASSIGNEMNT 1 ˙Power + 2 ˙Power +

- 3 - TABLE OF CONTENTS 1. INTRODUCTION 4 1.1 PACKAGE CONTENTS ...

- 30 - 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 Not used 6 Rx - (receive) Tx - (transmit) 7, 8 Not used

- 31 - Crossover Cable SIDE 1 SIDE2 SIDE 1 1234567812345678 SIDE 2 1 = White / Orange 2 = Orange 3 = White / Green 4 = Blue 5 = White / Blue 6

- 4 - 1. Introduction Thank you for purchasing IFS Layer 2 Industrial Gigabit Switch with 4-Port 802.3at PoE+, The MC352-4P-2S descriptions of the

- 5 - 1.3 Product Features Physical Port  MC352-4P-2S 4-Port 10/100/1000Base-T RJ-45 with IEEE 802.3af/802.3at PoE+ Injector 2 SFP interfaces,

- 6 - 1.4 Product Specifications Model MC352-4P-2S Hardware Specification Copper Ports 4 x 10/100/1000Base-T RJ-45 TP Auto-MDI/MDI-X, Auto-ne

- 7 - Switch Specification Switch Processing Scheme Store-and-Forward Address Table 1K entries Flow Control Back pressure for half duplex I

- 8 - 1.5 Physical Dimensions  MC352-4P-2S Industrial Gigabit PoE+ Switch dimensions (W x D x H): 161 x 107 x 72 mm

- 9 - 2. Installation This section describes the functionalities of the Industrial Gigabit PoE+ Switch’s components and guides how to install it o